Nurery pen is called weaning stall, it is designed to raising the new weaning piglets after the farrowing crates, usually the piglets from same mother sows will stay in the same weaning pen.usually single set weaning crate can keep 20-25 piglets, when piglets grop up above 35 kg, the piglets will switch to finishing pen..
Nurery pen is called weaning stall, it is designed to raising the new weaning piglets after the farrowing crates, usually the piglets from same mother sows will stay in the same weaning pen.usually single set weaning crate can keep 20-25 piglets, when piglets grop up above 35 kg, the piglets will switch to finishing pen.
Nusery pen is mainly composed of galvanized steel frame, PVC fence, stainless steel trough, drinking device, plastic floor and supporting beam.Generally, the adjacent area can share a double-sided stainless steel trough and PVC fence.
At present , Mus Agro have an annual production capacity output of 300,000 tons of various pig crates, in the stocks warehouse, there are sufficicent pig farm equipment for sales .
As one china nursery pen supplier, Mus Agro nursery stalls are designed scientifically, easy to install and operate, and can meet the pork production farm requirements of different scales pig farms , Mus Agro earned lots praises from the farms owners for farrowing crates good quality and service.
All of pig crates by Mus Agro are produced by high accuracy equipment for blanking welding and hot-dip galvanizing process, average zinc layer thickness above 85um,which can guarantee the long years service life, so as to make sure all pigs crates quality is well guaranteed
Nursery facilities, environmental control units, and equipment need to be properly prepared before the delivery of weaned pigs. When pigs arrive, they must find a place that is clean, warm, and draft-free with equipment (e.g., heaters, fans, lights, feeders, waterers, gates, etc.) already checked and adjusted for proper use.
Adjusting weaning pen equipment
In each pen, feeders and watering devices are two pieces of equipment that need special attention before pigs move in. Feeders must be cleaned and disinfected along with the rest of the facilities and equipment. Moreover, adjustment of the height or opening of feed gates is required. The best strategy to adjust an empty and clean feeder is to shut down the feed gate/opening and then fill the feeder with feed. By operating slowly the adjustment mechanism a small stream of feed must be allowed to flow through the opening to cover approximately one-third of the feeder pan. If the diet is fed in meal form then it is highly possible that it might bridge easily. Therefore, feeders must be rechecked after pigs start consuming feed.
It is recommended to fill feeders shortly after pigs arrive to stimulate their interest and avoid stale feed. No more than a day’s worth of feed should be placed in feeders during the very first days after weaning. Actually, offering feed two or even three times per day might increase feed intake in some occasions. Offering feed on a floor mat might also encourage pigs to eat but feed wastage could be excessive without a rim.
Water pipe and water bowl, also, should be carefully inspected in each and every pen because water consumption is even more important than feed intake during the first hours post weaning. If water cups are used, it is advisable to allow a small quantity of clean water to fill them right before or after pigs are placed in pens. This is especially helpful if pigs not used to drink from cups in farrowing houses. Nipple water bowl must be adjusted at shoulder-height based on the size of the average pig for each pen. It is recommended to let water trickle from nipples during the first couple of days or until pigs become familiar drinking from these devices.
If bedding is used then, it should be piled close to the assigned lying area and be allowed to reach room temperature before pigs arrive. Wet bedding should never be used. Other pen devices such as chains, toys, special feed and water dispensers must be cleaned and properly adjusted before placed in pens. Finally, all pen gates and locks must be checked and secured in place.
Disk chains feeding equipment production procedure Disk chain feeding steel chains bending and welding Hi Manganese steel wires are cut and bending and welding together with chains by the machine firstly, then finished chains process heat treatmen……
Learn MoreMus Agro-20 years experienced pig crates manufacturer in China As one 20 years experienced pig crates manufacturer in China, Mus Agro factory has complete advanced production equipment for the production of different types and styles pig crates, li……
Learn MoreMus Agro brief introduction Zhengzhou Mus Agro Tech Co., Ltd is located in Zhengzhou City, center place of People’s Republic of China, which is one professional pig equipment manufacturer from China. Mus Agro’s mission is to provide green and……
Learn MoreEgg conveyor belts for chicken layer cage egg collection system Egg conveyor belts is one hot sale egg collection system product for different types of layer cages, egg belts can influnce the egg collection systme performance, a good quality egg co……
Learn More