Mus Agro: Your reliable farm equipment supplier!
008618503860553
Most of the American style sow stall adopt the way of tilting the front door. It is said that the design consideration is that the tilting of the front door can increase the activity space of the pedestrian walkway at the front door. The use of round solid bar steel is considered that there is no galvanized hole and there is no risk of manure accumulation.
1.The size of the sow stall is 2200mm*650mm*1000mm, the outer frame is φ22 round solid bar steel, and the inner support is φ16 round solid bar steel.
2. The left and right double-opening latching structure is adopted. The thickness of the latching insert is not less than 5 mm, the exposed part is about 10 mm, and the door shaft door lock is limited to prevent the dislocation of the pig arch fence.
3. The feeding pipe is installed on the side of the fence separately. The direction of the feeding pipe mouth should be divided into left and right. The bottom of the feeding pipe is 150mm away from the ground, and the bottom end is polished without burrs; Ground height 1100mm;
4. Dimensions of the front and rear gates: the frame material of the gate is φ16 round solid bar steel.
5.There are three horizontal 4-point (φ21.3mm*2.0) galvanized steel pipes on each set of pig stall, the pipe wall thickness is 2.0mm, and the galvanized layer is not less than 275g/㎡ (the thickness of the zinc coating on one side is not less than 19.25μm).
For on-site installation, use SUS304 stainless steel M8 double U-shaped clips or M8 stainless steel bolts for punching and fixing, and the nuts are SUS304 self-locking nuts.
The ends must be protected with protective boots. The installation distance of the column is guaranteed to be 650mm±1mm, and the column and the connecting pipe do not slide and shift.
6. The height of the sow stall legs is 170mm, the size of the front footing plate is 130*50*5mm, and the size of the rear footing plate is 230*90*5mm. The four corners are rounded. The front footing plate uses SUS304M10 hexagonal flange expansion bolts. The steel plate is fixed on the slatted floor with SUS304M10 hexagonal flange bolts + large flat washers + M10 nylon blocks, and each anchor plate has no less than two fastening points.
7. The carbon steel materials not specified separately are all Q235, the overall hot-dip galvanizing of the bars and components, the overall hot-dip galvanizing, the thickness of the hot-dip galvanizing layer is ≥ 80 μm, the single point is not less than 70 μm, and the average thickness of the layers is not less than 65 μm.
8. All sow stall rails and components are connected by SUS 304 bolts + gaskets + self-locking nuts to prevent on-site welding.
9.M-type pig feeder trough: SUS034 stainless steel thickness 1.2mm; outer edge height 15cm, inner edge height 10cm, bottom width 18cm, top width 30cm. The troughs on both sides protrude about 10cm, and the side of the trough is drained (the level of the trough is not more than 10mm after installation, and the drainage port is located at a low position), and the 32mm drain pipe is designed on the side of the trough, protruding outside the fence, with stainless steel plugging; Design and installation shall facilitate cleaning of the trough.
1. The size of the sow stall is 2200mm×650mm×1000mm, the outer frame is φ22 round solid bar steel, and the inner support is φ16 round solid bar steel.
2. The sow stall front part of the column is inclined, with an inclination angle of about 18°, sows back in and front out.
3. The left and right double-opening latching structure is adopted. The thickness of the latching insert is not less than 5 mm, the exposed part is about 10 mm, and the door shaft door lock is limited to prevent the dislocation of the pig arch fence.
4. There is a rail with a blanking tube. The blanking tube is integrated with the side rail. The orientation of the blanking nozzle should be divided into left and right. The bottom of the blanking tube is 150mm away from the ground, and the bottom end is polished without burrs; After the material pipe is installed, the height of the upper edge from the ground is 1100mm;
5. The sow stall size of the rear entry and front exit gate: the frame material of the gate is φ16 round solid bar steel.
6. There are three horizontal 4-point (φ21.3mm*2.0) galvanized steel pipes on each set of pig stall to fix, the pipe wall thickness is 2.0mm, and the galvanized layer is not less than 275g/㎡ (the thickness of the zinc coating on one side is not less than 19.25μm). ). For on-site installation, use SUS304 stainless steel M8 double U-shaped clips or M8 stainless steel bolts for punching and fixing, and the nuts are SUS304 self-locking nuts. The ends must be protected with protective boots. The installation distance of the column is guaranteed to be 650mm±1mm, and the column and the connecting pipe do not slide and shift.
7. The height of the sow stall legs is 170mm, the size of the front footing plate is 130*50*5mm, and the size of the rear footing plate is 230*90*5mm. The four corners are rounded. The front footing plate uses SUS304M10 hexagonal flange expansion bolts. The steel plate is fixed on the slatted floor with SUS304M10 hexagonal flange bolts + large flat washers + M10 nylon blocks, and each anchor plate has no less than two fastening points.
8. The feeding tube adopts the side rail with its own feeding tube, adopts φ60*2.0 galvanized tube, and the bottom end is polished without burrs.
9. The carbon steel materials not specified separately are all Q235, the overall hot-dip galvanizing of the rails and components, the overall hot-dip galvanizing, the thickness of the hot-dip galvanizing layer is ≥ 80 μm, the single point is not less than 70 μm, and the average thickness of the layers is not less than 65 μm.
10. All sow stall rails and components are connected by SUS 304 bolts + gaskets + self-locking nuts to prevent on-site welding.
11.M-type pig feeder trough: SUS034 stainless steel thickness 1.2mm; outer edge height 15cm, inner edge height 10cm, bottom width 18cm, top width 30cm. The troughs on both sides protrude about 10cm, and the side of the trough is drained (the level of the trough is not more than 10mm after installation, and the drainage port is located at a low position), and the 32mm drain pipe is designed on the side of the trough, protruding outside the fence, with stainless steel plugging; Design and installation shall facilitate cleaning of the trough.
There is basically no big difference between the above 2 types sow stalls, only one small difference is that one of the fixing methods of the feed tube adopts an assembled type, and the other adopts a welded type.
Due to the weight differences, the price cost for solid bar steel sow stall is higher than Europe style round pipe style sow stall
