Mus Agro: Your reliable farm equipment supplier!
008618503860553
Round tube gestation stall for sale is one typical Europe style pig crates,it applies round tubes as the stall material,both outside and inside tube are hot dip galvanized,it is one widely used pig crates in modern swine farms.
1. Gestation stall for sale is 2200mm*650mm*1000mm, the outer frame adopts a φ26*2.3mm round tube; inner frame adopts φ21*2.3mm tubes; the feed tube is a φ60*2.0mm bent circular tube;The front and rear anchor plate is made of 5mm thick hot-rolled plate;
2. The gestation stall for sale front part of the column is inclined, the inclination angle is about 18°, and the back is in and out.
3. Back door: the outer frame is made of φ26*2.3mm round tube, with square lock mechanism and self-locking counterweight;
4. There is a rail with a blanking tube. The blanking tube is integrated with the side rail. The orientation of the blanking nozzle should be divided into left and right.
The bottom of the blanking tube is 150mm away from the ground, and the bottom end is polished without burrs; After the material pipe is installed, the height of the upper edge from the ground is 1100mm;
5. The front end of each set of gestation stall for sale has 4 channels and 4 branches (φ21.3mm*2.0), which are fixed by 304 stainless steel single U card, with 304 anti-loosening nuts, and the nuts are installed towards the outside of the bar body; there are three horizontal 4 points (φ21. 3mm*2.0) galvanized steel pipe is fixed, the wall thickness of the pipe is 2.0mm, and the galvanized layer is not less than 275g/㎡
For on-site installation, use SUS304 stainless steel M8 double U-shaped clips or M8 stainless steel bolts for punching and fixing, and the nuts are SUS304 self-locking nuts. The ends must be protected with protective boots. The installation distance of the column is guaranteed to be 650mm±1mm, and the column and the connecting pipe do not slide and shift.
7. The height of the gestation stall for sale legs of the limit bar is 170mm, the size of the front footplate is 130*50*5mm, and the size of the rear footplate is 230*90*5mm. The four corners are rounded.
The front footplate uses SUS304M10 hexagonal flange expansion bolts. The steel plate is fixed on the slatted floor with SUS304M10 hexagonal flange bolts + large flat washers + M10 nylon blocks, and each anchor plate has no less than two fastening points.
8. The carbon steel materials not specified separately are all Q235, the overall hot-dip galvanizing of the bars and components, the overall hot-dip galvanizing, the thickness of the hot-dip galvanizing layer is ≥ 80 μm, the single point is not less than 70 μm, and the average thickness of the layers is not less than 65 μm.
9. All rails and components are connected by SUS 304 bolts + gaskets + self-locking nuts to prevent on-site welding.
10.M-type pig feeder trough: SUS034 stainless steel thickness 1.2mm; outer edge height 15cm, inner edge height 10cm, bottom width 18cm, top width 30cm.
The troughs on both sides protrude about 10cm, and the side of the trough is drained (the level of the trough is not more than 10mm after installation, and the drainage port is located at a low position), and the 32mm drain pipe is designed on the side of the trough, protruding outside the fence, with stainless steel plugging;
1. Gestation stall for sale size is 2200mm*650mm*1000mm, the outer frame adopts a φ26*2.3mm round tube; inner frame adopts φ21*2.3mm tubes; the feed tube is a φ60*2.0mm bent circular tube;The front and rear anchor plate is made of 5mm thick hot-rolled plate;
2. The left and right double-opening latching structure is adopted. The thickness of the latching insert is not less than 5 mm, the exposed part is about 10 mm, and the door shaft door lock is limited to prevent the dislocation of the pig arch fence.
3. There is a rail with a blanking tube. The blanking tube is integrated with the side rail. The orientation of the blanking nozzle should be divided into left and right.
The bottom of the blanking tube is 150mm away from the ground, and the bottom end is polished without burrs; After the material pipe is installed, the height of the upper edge from the ground is 1100mm;
4. Gestation stall for sale front and rear gates: the outer frame adopts φ26*2.3mm round tube, and the vertical support adopts φ21*2.3mm round tube.
5. There are three horizontal 4-point (φ21.3mm*2.0) galvanized steel pipes on each set of limit bars to fix, the pipe wall thickness is 2.0mm, and the galvanized layer is not less than 275g/㎡ (the thickness of the zinc coating on one side is not less than 19.25μm).
For on-site installation, use SUS304 stainless steel M8 double U-shaped clips or M8 stainless steel bolts for punching and fixing, and the nuts are SUS304 self-locking nuts. The ends must be protected with protective boots.
The installation distance of the column is guaranteed to be 650mm±1mm, and the column and the connecting pipe do not slide and shift.
6. The gestation stall for sale height is 170mm, the size of the front footplate is 130*50*5mm, and the size of the rear footplate is 230*90*5mm. The four corners are rounded.
7. The feeding tube of gestation stall for sale adopts the side rail with its own feeding tube, adopts φ60*2.0 galvanized tube, and the bottom end is polished without burrs.
8. Gestation stall for sale steel materials are all Q235, the overall hot-dip galvanizing of the rails and components, the overall hot-dip galvanizing, the thickness of the hot-dip galvanizing layer is ≥ 80 μm, the single point is not less than 70 μm,the average thickness of the layers is not less than 65 μm.
9. All gestation stall for sale rails and components are connected by SUS 304 bolts + gaskets + self-locking nuts to prevent on-site welding.
10.M-type long trough: SUS034 stainless steel thickness 1.2mm; outer edge height 15cm, inner edge height 10cm, bottom width 18cm, top width 30cm.
The troughs on both sides protrude about 10cm, and the side of the trough is drained (the level of the trough is not more than 10mm after installation, and the drainage port is located at a low position), and the 32mm drain pipe is designed on the side of the trough, protruding outside the fence, with stainless steel plugging;
